This is a summary of a paper of the same title, authored by K. Májlinger, E. Kalácska, and P. Russo Spena, used by permission.M-65

 

Researchers at the Budapest University of Technology and Economics and the Free University of Bozen-Bolzano tested gas metal arc welding (GMAW) of dissimilar Advanced High-Strength Steel (AHSS) sheets.M-65 The test pieces were 100 x 50 mm samples of 1.4 mm TWIP (TWIP1000) and 0.9 mm TRIP (HCTC800T) sheet steels were welded in a lap joint configuration with 0.8 mm diameter AWS ER307Si austenitic stainless steel wire to determine appropriate GMAW parameters for good quality welds. Quality was determined by external appearance, microstructure, and mechanical properties. Good welds were achieved with linear heat inputs (Q) with ranges from 500-650 kJ/m. The only fractures that occurred appeared within the weld bead by ductile failure modes. The HAZ of the TWIP steel showed grain coarsening and the HAZ of the TRIP steel experienced microstructural changes relative to the distance from the fusion boundary. The ultimate tensile strength (UTS) varies between 73%-84% of the weaker of the two steels.

Welding was conducted with an automated linear drive system with pure Argon (99.996% Ar) shielding gas at 10L/min. Wire feed rates were approximately 3.5 m/min with Direct Current Electrode Positive (DCEP) polarity. Changes in current, voltage, weld speed, and the resulting linear energy are compared in Table 1.

Figure 1: Overview of Dissimilar AHSS GMAW Welding.M-65

Figure 1: Overview of Dissimilar AHSS GMAW Welding.M-65

 

Table 1: Results of the preliminary welding tests in terms of TWIP-TRIP joint quality.M-65

Table 1: Results of the preliminary welding tests in terms of TWIP-TRIP joint quality.M-65

 

After welding, transverse sections were cut from the welds and etched to show the microstructure. Vickers hardness testing was conducted on the weld samples based on the ASTM E384 standard. Tensile tests were performed on the samples according to the EN ISO 6892-1 standard. Tests were also conducted on unwelded TWIP and TRIP steels for comparison. Scanning electron microscopy (SEM) examinations were made of fracture surfaces to determine failure modes and examine for microscopic weld defects.

The study concluded that dissimilar welds between AHSS steels with the GMAW process can be achieved with consistent results desired for automotive applications.

Figure 2: Vickers Hardness Across Weldment.M-65

Figure 2: Vickers Hardness Across Weldment.M-65

 

Figure 3: Ductile Failure in FZ.M-65

Figure 3: Ductile Failure in the fragile zones (FZ).M-65

 

 

Related Posts
Filter by
Post Page
Joining Arc Welding Citations Projection Welding Automotive Welding Process Comparison High Energy Density Welding
Sort by

HAZ Properties of GMAW DP 600

In production, part geometry or joint application requires the use of gas metal arc welding (GMAW) to weld the

18

Fatigue of GMAW-P Lap Joints

This article summarizes a paper by W. Mohr and N. Kapustka,

18

Microstructure and Softening QP1180 Lap Joints Welded with CMT

Quenching and partitioning (QP) steels are one of several third generation advanced high strength steel formed by

8

Role of Coatings in the Formation of Defects in AHSS Welds

A common issue when welding Advanced High-Strength Steels (AHSS) is with protective coatings causing weld defects. A

8

R-24

Citation: R-24. A. Ramazani, K. Mukherjee, A. Abdurakhmanov, U.

8

Projection Welding

As with resistance spot welding in automotive applications, projection welding also is used to join two overlapping

8

M-13

Citation: M-13.  W. Mohr and N. Kapustka, “Fatigue of GMAW-P Lap Joints in Advanced H

8